Hi i use accel-ppp with this config
[modules]
log_file
#log_syslog
#log_tcp
#log_pgsql
#pptp
#l2tp
#sstp
pppoe
#ipoe
#auth_mschap_v2
#auth_mschap_v1
#auth_chap_md5
auth_pap
radius
#chap-secrets
pppd_compat
#shaper
#net-snmp
#logwtmp
#connlimit
#ipv6_nd
#ipv6_dhcp
#ipv6pool
ippool
[core]
log-error=/var/log/accel-ppp/core.log
thread-count=4
[common]
#single-session=replace
#sid-case=upper
#sid-source=seq
#max-sessions=1000
[ppp]
verbose=1
min-mtu=1280
mtu=1496
mru=1496
#accomp=deny
#pcomp=deny
ccp=0
check-ip=0
#mppe=require
ipv4=require
ipv6=allow
ipv6-intf-id=0:0:0:1
ipv6-peer-intf-id=0:0:0:2
ipv6-accept-peer-intf-id=1
lcp-echo-interval=20
lcp-echo-failure=3
lcp-echo-timeout=120
unit-cache=1
#unit-preallocate=1
[auth]
#any-login=0
#noauth=0
[pptp]
#verbose=1
#echo-interval=30
#ifname=pptp%d
[pppoe]
verbose=1
ac-name=pppoe2
#service-name=pppoe22
#pado-delay=0
#pado-delay=0,100:100,200:200,-1:500
called-sid=ifname
#tr101=1
#padi-limit=0
ip-pool=pppoe
ip-pool=pppoe2
#ifname=pppoe%d
sid-uppercase=1
#vlan-mon=enp1s0f3,10-40
#vlan-timeout=60
#vlan-name=%I.%N
#interface=eth1,padi-limit=1000
#interface=eth0
interface=re:enp1s0f3.([1-9]|[1-9][0-9]|[1-9][0-9][0-9]|[1-4][0-9][0-9][0-9])
#interface=enp1s0f3.11,padi-limit=1000
#interface=enp1s0f3.12,padi-limit=1000
#interface=enp1s0f3.13,padi-limit=1000
#interface=enp1s0f3.14,padi-limit=1000
#interface=enp1s0f3.15,padi-limit=1000
#interface=enp1s0f3.16,padi-limit=1000
#interface=enp1s0f3.17,padi-limit=1000
#interface=enp1s0f3.18,padi-limit=1000
interface=enp1s0f3.19,padi-limit=1000
#interface=enp1s0f3.20,padi-limit=1000
#interface=enp1s0f3.21,padi-limit=1000
#interface=enp1s0f3.22,padi-limit=1000
#interface=enp1s0f3.26,padi-limit=1000
#interface=enp1s0f3.27,padi-limit=1000
#interface=enp1s0f3.28,padi-limit=1000
#interface=enp1s0f3.29,padi-limit=1000
#interface=enp1s0f3.30,padi-limit=1000
#interface=enp1s0f3.31,padi-limit=1000
#interface=enp1s0f3.32,padi-limit=1000
#interface=enp1s0f3.33,padi-limit=1000
#interface=enp1s0f3.34,padi-limit=1000
[l2tp]
#verbose=1
#dictionary=/usr/local/share/accel-ppp/l2tp/dictionary
#hello-interval=60
#timeout=60
#rtimeout=1
#rtimeout-cap=16
#retransmit=5
#recv-window=16
#host-name=accel-ppp
#dir300_quirk=0
#secret=
#dataseq=allow
#reorder-timeout=0
#ip-pool=l2tp
#ifname=l2tp%d
[dns]
dns1=8.8.8.8
dns2=8.8.8.8
[wins]
wins1=8.8.8.8
wins2=8.8.8.8
[radius]
dictionary=/usr/local/share/accel-ppp/radius/dictionary
nas-identifier=pppoe2-accel
nas-ip-address=127.0.0.1
gw-ip-address=10.10.10.1
server=127.0.0.1,testisav,auth-port=1812,acct-port=1813,req-limit=50,fail-timeout=0,max-fail=10,weight=1
dae-server=127.0.0.1:3799,testis
verbose=1
timeout=3
max-try=3
#acct-timeout=120
#acct-delay-time=0
#acct-on=0
#attr-tunnel-type=My-Tunnel-Type
[client-ip-range]
#10.0.0.0/8
disable
[ip-pool]
gw-ip-address=10.10.10.1
#vendor=Cisco
#attr=Cisco-AVPair
#attr=Framed-Pool
attr=Framed-IP-Address
10.10.150.1/24,name=pppoe,next=pppoe2
10.10.151.1/24,name=pppoe2
[log]
log-file=/var/log/accel-ppp/accel-ppp.log
log-emerg=/var/log/accel-ppp/emerg.log
log-fail-file=/var/log/accel-ppp/auth-fail.log
log-debug=/var/log/accel-ppp/debug.log
#syslog=accel-pppd,daemon
#log-tcp=127.0.0.1:3000
copy=0
color=1
#per-user-dir=per_user
#per-session-dir=per_session
#per-session=1
level=7
[log-pgsql]
conninfo=user=log
log-table=log
[pppd-compat]
verbose=1
ip-pre-up=/etc/ppp/auth-up
ip-up=/etc/ppp/ip-up
ip-down=/etc/ppp/ip-down
#ip-change=/etc/ppp/ip-change
radattr-prefix=/var/run/radattr
#fork-limit=16
[chap-secrets]
#gw-ip-address=192.168.100.1
#chap-secrets=/etc/ppp/chap-secrets
#encrypted=0
#username-hash=md5
[shaper]
#attr=Filter-Id
#down-burst-factor=0.1
#up-burst-factor=1.0
#latency=50
#mpu=0
#mtu=0
#r2q=10
#quantum=1500
#moderate-quantum=1
#cburst=1534
#ifb=ifb0
#up-limiter=police
#down-limiter=tbf
#leaf-qdisc=sfq perturb 10
#leaf-qdisc=fq_codel [limit PACKETS] [flows NUMBER] [target TIME] [interval TIME] [quantum BYTES] [[no]ecn]
#rate-multiplier=1
#fwmark=1
#verbose=1
[cli]
verbose=1
telnet=127.0.0.1:2000
tcp=127.0.0.1:2001
#password=123
sessions-columns=ifname,username,ip,ip6,ip6-dp,type,state,uptime,uptime-raw,calling-sid,called-sid,sid,comp,rx-bytes,tx-bytes,rx-bytes-raw,tx-bytes-raw,rx-pkts,tx-pkts
[snmp]
master=0
agent-name=accel-ppp
[connlimit]
limit=10/min
burst=3
timeout=60
[ipv6-pool]
#gw-ip6-address=fc00:0:1::1
fc00:0:1::/48,64
delegate=fc00:1::/36,48
[ipv6-dns]
#fc00:1::1
#fc00:1::2
#fc00:1::3
#dnssl=suffix1.local.net
#dnssl=suffix2.local.net.
[ipv6-dhcp]
verbose=1
pref-lifetime=604800
valid-lifetime=2592000
route-via-gw=1
###########################
and have problem with ippool
from log:
[2019-01-08 14:41:15.972] ippool: 10.10.150.1/24,name=pppoe,next=pppoe2: next pool not found
and
ppp: no free IPv4 address
when ip address from first pool is finish
and this version accel-cmd 2910add2238d419ad82e43f3ebf1fb8d5708e13b
?
next pool not found
Re: next pool not found
From docs:
Try change from:
to:
Code: Select all
next pool must be defined before being referenced
Code: Select all
10.10.150.1/24,name=pppoe,next=pppoe2
10.10.151.1/24,name=pppoe2
Code: Select all
10.10.151.1/24,name=pppoe2
10.10.150.1/24,name=pppoe,next=pppoe2
-
- Posts: 5
- Joined: 09 Jan 2019, 13:13
Re: next pool not found
Hi , it works !
i have another question for backup radius server? How to configure it?
Merci!
i have another question for backup radius server? How to configure it?
Merci!
Re: next pool not found
Hi, https://accel-ppp.org/accel-ppp.conf.htmlvillagenet wrote: ↑10 Jan 2019, 13:07 i have another question for backup radius server? How to configure it?
server=address,secret[,auth-port=1812][,acct-port=1813][,req-limit=0][,fail-timeout=0,max-fail=0,][,weight=1][,backup]
Specifies IP address, secret, ports of RADIUS server.
req-limit - number of simultaneous requests to server (0 - unlimited).
fail-time - if server doesn't responds mark it as unavailable for this time (sec).
max-fail - number of unreplied requests in a row after that mark server as unavailable.
weight - specifies weight of server for multi-server configuration.
backup - mark server as backup server f.e. use this server only when all other servers are failed.
If you want to specify only authentication or accounting server then set auth-port/acct-port to zero. You may specify multiple radius servers.
Code: Select all
[radius]
server=10.0.0.1,secret,auth-port=1812,acct-port=1813,req-limit=0,fail-timeout=3,max-fail=5
server=10.0.0.2,secret,auth-port=1812,acct-port=1813,req-limit=0,fail-timeout=0,max-fail=0,backup
-
- Posts: 5
- Joined: 09 Jan 2019, 13:13
Re: next pool not found
Hi
works all .Tnx about the answers. I have PPPoe server with dinamic ip adresses. How can I make every user graphic in case they use dinamic Ip adresses? is it possible?Do you have any scripts?
works all .Tnx about the answers. I have PPPoe server with dinamic ip adresses. How can I make every user graphic in case they use dinamic Ip adresses? is it possible?Do you have any scripts?
Re: next pool not found
Hi, meny accel-ppp users parse output of command accel-cmd show sessions with zabbix-agent and create graphs with zabbix system.
Output of command accel-cmd show sessions support next argumens in config accel-ppp and confirm on accel-cmd reload without daemon restart
Output of command accel-cmd show sessions support next argumens in config accel-ppp and confirm on accel-cmd reload without daemon restart
Code: Select all
[cli]
verbose=1
telnet=127.0.0.1:2000
tcp=127.0.0.1:2001
sessions-columns=ifname,username,ip,ip6,ip6-dp,type,state,uptime,uptime-raw,calling-sid,called-sid,sid,comp,rx-bytes,tx-bytes,rx-bytes-raw,tx-bytes-raw,rx-pkts,tx-pkts
-
- Posts: 5
- Joined: 09 Jan 2019, 13:13
Re: next pool not found
hi I installed zabbix-server and zabbix-agent but zabbix is the complex system, and not have teplates for captures trafik for all pppoe user. Do you have script or templates?
Re: next pool not found
Code: Select all
<?xml version="1.0" encoding="UTF-8"?>
<zabbix_export>
<version>4.0</version>
<date>2019-02-07T13:02:37Z</date>
<groups>
<group>
<name>BNG</name>
</group>
<group>
<name>Templates</name>
</group>
</groups>
<templates>
<template>
<template>Accel IPoE</template>
<name>Accel</name>
<description/>
<groups>
<group>
<name>BNG</name>
</group>
<group>
<name>Templates</name>
</group>
</groups>
<applications>
<application>
<name>Accel</name>
</application>
</applications>
<items>
<item>
<name>Accel Online Users</name>
<type>7</type>
<snmp_community/>
<snmp_oid/>
<key>accel.onlineusers</key>
<delay>1m</delay>
<history>90d</history>
<trends>365d</trends>
<status>0</status>
<value_type>3</value_type>
<allowed_hosts/>
<units>Users</units>
<snmpv3_contextname/>
<snmpv3_securityname/>
<snmpv3_securitylevel>0</snmpv3_securitylevel>
<snmpv3_authprotocol>0</snmpv3_authprotocol>
<snmpv3_authpassphrase/>
<snmpv3_privprotocol>0</snmpv3_privprotocol>
<snmpv3_privpassphrase/>
<params/>
<ipmi_sensor/>
<authtype>0</authtype>
<username/>
<password/>
<publickey/>
<privatekey/>
<port/>
<description/>
<inventory_link>0</inventory_link>
<applications>
<application>
<name>Accel</name>
</application>
</applications>
<valuemap/>
<logtimefmt/>
<preprocessing/>
<jmx_endpoint/>
<timeout>3s</timeout>
<url/>
<query_fields/>
<posts/>
<status_codes>200</status_codes>
<follow_redirects>1</follow_redirects>
<post_type>0</post_type>
<http_proxy/>
<headers/>
<retrieve_mode>0</retrieve_mode>
<request_method>1</request_method>
<output_format>0</output_format>
<allow_traps>0</allow_traps>
<ssl_cert_file/>
<ssl_key_file/>
<ssl_key_password/>
<verify_peer>0</verify_peer>
<verify_host>0</verify_host>
<master_item/>
</item>
<item>
<name>Accel Start Sessions</name>
<type>7</type>
<snmp_community/>
<snmp_oid/>
<key>accel.startsessions</key>
<delay>1m</delay>
<history>1w</history>
<trends>365d</trends>
<status>0</status>
<value_type>3</value_type>
<allowed_hosts/>
<units>Sessions</units>
<snmpv3_contextname/>
<snmpv3_securityname/>
<snmpv3_securitylevel>0</snmpv3_securitylevel>
<snmpv3_authprotocol>0</snmpv3_authprotocol>
<snmpv3_authpassphrase/>
<snmpv3_privprotocol>0</snmpv3_privprotocol>
<snmpv3_privpassphrase/>
<params/>
<ipmi_sensor/>
<authtype>0</authtype>
<username/>
<password/>
<publickey/>
<privatekey/>
<port/>
<description/>
<inventory_link>0</inventory_link>
<applications>
<application>
<name>Accel</name>
</application>
</applications>
<valuemap/>
<logtimefmt/>
<preprocessing/>
<jmx_endpoint/>
<timeout>3s</timeout>
<url/>
<query_fields/>
<posts/>
<status_codes>200</status_codes>
<follow_redirects>1</follow_redirects>
<post_type>0</post_type>
<http_proxy/>
<headers/>
<retrieve_mode>0</retrieve_mode>
<request_method>1</request_method>
<output_format>0</output_format>
<allow_traps>0</allow_traps>
<ssl_cert_file/>
<ssl_key_file/>
<ssl_key_password/>
<verify_peer>0</verify_peer>
<verify_host>0</verify_host>
<master_item/>
</item>
</items>
<discovery_rules/>
<httptests/>
<macros/>
<templates/>
<screens/>
</template>
</templates>
<graphs>
<graph>
<name>Accel Online Users</name>
<width>900</width>
<height>200</height>
<yaxismin>0.0000</yaxismin>
<yaxismax>100.0000</yaxismax>
<show_work_period>1</show_work_period>
<show_triggers>1</show_triggers>
<type>0</type>
<show_legend>1</show_legend>
<show_3d>0</show_3d>
<percent_left>0.0000</percent_left>
<percent_right>0.0000</percent_right>
<ymin_type_1>0</ymin_type_1>
<ymax_type_1>0</ymax_type_1>
<ymin_item_1>0</ymin_item_1>
<ymax_item_1>0</ymax_item_1>
<graph_items>
<graph_item>
<sortorder>0</sortorder>
<drawtype>5</drawtype>
<color>FF6F00</color>
<yaxisside>0</yaxisside>
<calc_fnc>2</calc_fnc>
<type>0</type>
<item>
<host>Accel IPoE</host>
<key>accel.onlineusers</key>
</item>
</graph_item>
</graph_items>
</graph>
<graph>
<name>Accel Start Sessions</name>
<width>900</width>
<height>200</height>
<yaxismin>0.0000</yaxismin>
<yaxismax>100.0000</yaxismax>
<show_work_period>1</show_work_period>
<show_triggers>1</show_triggers>
<type>0</type>
<show_legend>1</show_legend>
<show_3d>0</show_3d>
<percent_left>0.0000</percent_left>
<percent_right>0.0000</percent_right>
<ymin_type_1>0</ymin_type_1>
<ymax_type_1>0</ymax_type_1>
<ymin_item_1>0</ymin_item_1>
<ymax_item_1>0</ymax_item_1>
<graph_items>
<graph_item>
<sortorder>0</sortorder>
<drawtype>5</drawtype>
<color>FFA000</color>
<yaxisside>0</yaxisside>
<calc_fnc>2</calc_fnc>
<type>0</type>
<item>
<host>Accel IPoE</host>
<key>accel.startsessions</key>
</item>
</graph_item>
</graph_items>
</graph>
and two keys for userparameter.cnf, but I have ipoe you have to fix for yourself (pppoe)
UserParameter=accel.startsessions,/usr/local/bin/accel-cmd show stat | grep -A 4 "ipoe" | sed -e '/ipoe/d' -e '/active/d' -e '/delayed/d' -e 's/ starting: //g'
UserParameter=accel.onlineusers,/usr/local/bin/accel-cmd show stat | grep -A 4 "ipoe" | sed -e '/ipoe/d' -e '/starting/d' -e '/delayed/d' -e 's/ active: //g'